Fix cybran T3 shielding

Any specific reduction in mass / resources that you have in mind?
5%? 10%? 15%?

I like your idea of making the ED5 the standard blueprint, however...
I'm not too sure you want to increase the Cybran's Mass to SHP efficiency, dramatically.
Cybrans, even with their higher mass cost at a glance; they still have quite efficient shields for what they're worth.

For example, the UEF has the least efficient shields with their high costs and low SHP to compensate.

Cybrans, may have high mass costs, but their SHP is higher than that of a UEF shield.


~ Stryker

( ͡° ͜ʖ ͡°)

It's 16.5k for cyb to 17k for uef, while cyb costs 4260 and uef 3300

profile picture credits to petric

@waffelznoob said in Fix cybran T3 shielding:

Balance team thankfully doesn't have the same mindset as you, as they buffed the aeon frigate despite aeon having the strongest destroyer.

Exodus:

  • HP: 7500 > 7200
  • Range: 80 > 70

Exodus was so stacked it still is the strongest destroyer lol

profile picture credits to petric

@waffelznoob said in Fix cybran T3 shielding:

It's 16.5k for cyb to 17k for uef, while cyb costs 4260 and uef 3300

Is the extra mass worth an instant refresh on the SHP?
I say it is very much worth it. Cybrans have one of the best shields, because of that ability.
They upgrade, and they refresh their shield HP.

Granted, they're not the cheapest when it comes to their shields, but that gives them more flexability and longevity, especially when it comes down to protecting a valuable target.
The shield may have been depleted, and offline, but now it isn't.


If you make the ED5 Blueprint the standard instead of the ED4: Shield refreshes will be seen a few less times.
So, this could make a decent reason to lower the Cybran's Shields costs globally.

Perhaps, reduce the costs of the, ED4, and ED5 by 5% each? As a player upgrades them, the savings stack, meaning you end up saving more than just the 5% of each tier. That would make the ED5 shield about. 7-10% cheaper, in total?


~ Stryker

( ͡° ͜ʖ ͡°)

I would once again suggest removing instant full hp on shield upgrade and have it keep its current hp upon upgrade but get a new maximum

it makes no sense it does that and makes it better to keep shields on 99% upgrade to suddenly reload them if they get low by upgrading

anybody doing that micro is a genetic freak

  1. having enough bp to spend 1800 mass inbetween t3 arty/mavor shots sounds pretty unrealistic
  2. it is a one-time thing, u can not repeat it for future arty shells
  3. nobody does that with ED4 -> ED5 shields lol

5-10% is not enough. Give me one good reason as to why T3 cybran shields should be both weaker and more expensive.

profile picture credits to petric

UEF is strong alpha faction and cybran is weak nerds.

weak nerds... with lasers

@waffelzNoob bro i think you should be on the balance team. enough said, you are right ahah

Only tangentially related and idk if I'm the only one who thinks this, but shield assisting with 10 hives is lame af. Building a good simcity with lots of t3 shields should be more efficient than putting ur mavor under 1 shield assisted by 10 hives

@blodir said in Fix cybran T3 shielding:

Only tangentially related and idk if I'm the only one who thinks this, but shield assisting with 10 hives is lame af. Building a good simcity with lots of t3 shields should be more efficient than putting ur mavor under 1 shield assisted by 10 hives

And while we're at it, the engis/hives shouldn't stop assisting once the shield is at full hp. It just forces u to stare at ur hives for the rest of the game in an arty/sat war

@blodir said in Fix cybran T3 shielding:

Only tangentially related and idk if I'm the only one who thinks this, but shield assisting with 10 hives is lame af. Building a good simcity with lots of t3 shields should be more efficient than putting ur mavor under 1 shield assisted by 10 hives

At the moment overspill works such that:

  • shield that is hit takes full damage
  • on top of that, surrounding shields take a bit of that damage too

But we can change it to:

  • shield that takes full damage disperses it over neighboring shields, depending on distance to that shield

That way it is better to have a lot of shields than having 1 shield being assisted. It would also add a lot of value to the lower tier cybran shields: they collapse sooner due to the dispersion damage and can recover quickly to support the higher tech shields again

And while we're at it, the engis/hives shouldn't stop assisting once the shield is at full hp. It just forces u to stare at ur hives for the rest of the game in an arty/sat war

Engine behavior I'm afraid

A work of art is never finished, merely abandoned

@blodir A related annoyance I have is that assisting shields isnt limited by eco meaning at high BP assistance levels you end up restoring much more shield health per mass than it costs (thus incentivising massive assistance further).

@jip said in Fix cybran T3 shielding:

@blodir said in Fix cybran T3 shielding:

Only tangentially related and idk if I'm the only one who thinks this, but shield assisting with 10 hives is lame af. Building a good simcity with lots of t3 shields should be more efficient than putting ur mavor under 1 shield assisted by 10 hives

At the moment overspill works such that:

  • shield that is hit takes full damage
  • on top of that, surrounding shields take a bit of that damage too

But we can change it to:

  • shield that takes full damage disperses it over neighboring shields, depending on distance to that shield

That way it is better to have a lot of shields than having 1 shield being assisted. It would also add a lot of value to the lower tier cybran shields: they collapse sooner due to the dispersion damage and can recover quickly to support the higher tech shields again

And while we're at it, the engis/hives shouldn't stop assisting once the shield is at full hp. It just forces u to stare at ur hives for the rest of the game in an arty/sat war

Engine behavior I'm afraid

Sounds good imo, though requires some testing/experimentation. Shield overspill was added in FAF iirc, so I assume that it was added for a reason. I seem to recall it being added mostly about bulwark stacking making navy unkillable, but could be wrong. Mby bulwark stacking could be nerfed some other way...

@blodir said in Fix cybran T3 shielding:

Shield overspill was added in FAF iirc, so I assume that it was added for a reason.

stacking shields in general is op without overspill, you take out one shield and another full hp one is behind it (and another one after that, and another after, and...), in steam FA bases can become basically unkillable other than with nukes or air crash

@jip would be cool way to make arties less effective but that would be a fat buff to firebases and bulwarks

profile picture credits to petric

Don’t forget parashield and asylum stacking god bless

@waffelznoob said in Fix cybran T3 shielding:

@jip would be cool way to make arties less effective but that would be a fat buff to firebases and bulwarks

You could make it work only for artillery. Wouldn't be unique - the xbox game even ships a UEF Artillery shield. All of the logic is all in the source code already, just unused

A work of art is never finished, merely abandoned